OW N E R ’S OP E R A T I N G MA N U A LCR-26HDwithCrystal Series™ LCD Displays
10Control PanelsCR-26HD Rear View and Input Panel1 INPUT2 S-Video Input2 INPUT2 Audio Input3 INPUT2 Video Input4 Headphone Jack5 Power Input6 RG
11Remote ControlNote:• Makes sure there are no objects between the remote control and its sensor.• Don’t place the remote control near a heater
12Connecting an Antenna or CableConnecting to the Video or S-Video Input (INPUT1 or INPUT2)To view television channels, a signal must be input
13Using the MONITOR OUT featureConnecting to a DVD or DTV Set-Top Box INPUT (RCA or DVI)ConnectionsINPUT4INPUT31. Connect the video cables to the Y,
14Connecting to a PCConnectionsTo use the display as a PC Monitor1. Turn the PC on.2. Depending on the connection, press the DVI or RGB HD button on t
15ConnectionsSetting the PC PropertiesConnecting Headphones1. First, click on Settings on the Windows Start menu and click on “Control Panel”.2. Doub
16Basic OperationsConnecting the Power Cord and Switching the Display On / OffSelecting a Source4 501001 236TIMEROFFINPUT17 8 9OFF ONINPUT2INPUT3INPUT
17Selecting an Aspect RatioBasic Operations1. Press the MENU button on the remote control.2. Press the ▲▼ buttons to select Aspect Ratio and then pr
18Selecting Picture AdjustBasic Operations1. Press the MENU button on the remote control.2. Press the ▲▼ button to select PICTURE ADJUST and then pre
19Equalizer1. Press the ▲▼ buttons to select Equalizer and then press the ENTER or ► button.2. Press the ▲▼ buttons to select Standard, Music, Film, S
Table of ContentsOne Year Limited Warranty ...4Introduction ...
20Selecting TimerAuto Tuning Add /EraseBasic Operations1. Press the MENU button on the remote control.2. Press the ▲▼ buttons to select Timer and the
211. Press the MENU button on the remote control.2. Press the ▲▼ buttons to select Setup and then press the ENTER or ► button.3. Press the ▲▼ buttons
22Setup1. Press the ▲▼ buttons to select Parental Control and then press the ENTER or ► button.2. Enter your 4-digit PIN number to access the P
23Monitor OutOverscanInput Selection1. Press the ▲▼ buttons to select Input Selection and then press the ENTER or ► button.2. Press the ▲▼ button
24ISF CalibrationTo be used by Runco Service Technician or ISF Certified personnel. A passcode is required to access the ISF Calibration window.
25Blue EnableISF Calibration Picture Adjust White Balance Blue Enable DNR Gamma Baud Rate Command Ack Factory Reset Splash Duration
26Displaying the Picture in Picture (PIP)1. Press the PIP ( ) button. There are 2 modes of PIP window : Small, Twin. Whenever you press th
27Picture in Picture (PIP)Changing the PIP SizeSelecting the Image Size in the PIPSelecting the Image Mode in the PIPChanging the PIP Position1. Press
28Swapping the Main & Sub-PictureSwapping the Main & Sub-SoundPicture in Picture (PIP)1. Press the ( ) button on the remote control. • The Ma
29Changing the PIP Aspect RatioPicture in Picture (PIP)1. Press the ( ) button on the remote control. • When you are viewing the Main image: The i
3ISF Calibration (Service)Picture Adjust ...
30Listening to Stereo Sound / SAP OptionM S SAP M+SAPBroadcastingMM M M MSM S M SM+SAPM M SAP M+SAPS+SAPM S SAP M+SAP
31RS-232C ConfigurationsNote: • All commands are in ASCII format • Default baud rate is 115200,8,N,1, but can be changed (see page 25) • No carriag
32‘[‘ + ‘S3A’ + ‘000#’ Set audio volume to ### (=000~100)Example: [ S3A000075 sets volume to 75‘[‘ + ‘+3A’ Audio volume up‘[‘ + ‘- 3A Audio volume d
33RS-232 ConfigurationsThe following serial commands are meant to emulate buttons on the remote control. Each button has its own serial command, so ef
34If the signal from the system equals the standard signal mode, the screen will adjust automatically. If the signal from the system does not equal th
35PC Input Connector (D-Sub 15Pin)DVI-D Connector Pin PC INPin PC IN1 Red (R)8Blue (B) Ground2 Green (G)9 Reserved3 Blue (B)10Sync Ground4 Ground11Gro
36For Display PanelTroubleshootingNo picture or sound.• Make sure the display is plugged in.• Make sure the power cord is connected correctly.• Check
37“No signal” message• Check if the signal cable (DVI Cable) is properly connected to the computer. (See page 14)“Out of range” message• This messag
38SpecificationsNative Resolution:1366 x 768 WXGAScreen Size:26 in. (diagonal)Screen Aspect Ratio:16:9Available Aspect Ratios:4:3, Letterbox, 16:9 Ana
39Dimensions26 in. (660 mm)27 in. (686 mm)7.563 in. (192 mm)20 in.(508 mm)3.375 in. (86 mm)
One Year Limited Warranty4Congratulations on your purchase of Runco’s latest video product and welcome to the Runco family! We believe Runco produces
Runco International • 2900 Faber Street • Union City, CA 94587 • Ph (510) 324-7777 / (800) 23RUNCO / Fax (510) 324-9300www.runco.comRUMA-011090rev 7-1
5This Limited Warranty only covers failure due to defects in materials and workmanship that occur during normal use and does not cover normal maintena
6RUNCO VIDEO PRODUCT INFORMATION RETAIN THIS INFORMATION FOR YOUR RECORDS Model Purchased Date
7IntroductionRunco presents the high performance Crystal Series™ CR-26HD LCD display, perfect for those who demand our award-winning flat panel perfor
8CAUTIONTo turn off main power, be sure to remove the plugs from power outlets. The power outlet socket should be installed as near to the equipment a
9CR-26HD Front ViewControl Panels1 TV/AV Button (Input Source Selection)2 MENU Selection Button3 Volume Adjustment Buttons4 Channel Selection Bu
Kommentare zu diesen Handbüchern