Runco D-73d Ultra Spezifikationen Seite 72
- Seite / 152
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Installation
56 D-73d Series Installation/Operation Manual
11. Adjust Horizontal Offset on Left (Top) Primary Lens: To shift the projected
image horizontally, insert the provided hex wrench into the horizontal lens shift
adjuster at the top of the projector. Then, turn the wrench as shown to shift the lens
in the desired direction.
12. Lock Left (Top) Primary Lens Position and Zoom Settings: When you have
finished adjusting the lens position and image size (zoom), insert the provided hex
wrench into the lens lock access hole at the front of the projector. Then, turn the
wrench clockwise two or three full turns to lock the lens position.
Right (Bottom) Primary Lens Adjustment:
1. On the Dimension Digital Controller remote control or front panel, press MENU.
2. Select Calibration from the Main Menu.
3. Select Adjustment Mode from the Calibration Menu and set it to Secondary.
4. Press EXIT (or MENU) repeatedly to return to the Main Menu.
5. Select Service from the Main Menu.
6. Select Test Video from the Service Menu and choose Secondary Alignment.
7. Perform Steps 8 through 12 above with the right (bottom) primary lens.
When you have completed the primary lens adjustments (D-73d/CineWide with
AutoScope only): Remove the anamorphic lenses and set the lens transport motor
power switch to the “on” position.
Adjusting the Picture
Orientation
By default, the D-73d is configured for a “floor/front” installation, in which the projector is
installed upright and in front of the screen. If it is installed behind the screen and/or
mounted on a ceiling, you must change the picture orientation. To do this:
1. On the Dimension Digital Controller remote control or front panel, press MENU.
2. Select Service from the Main Menu.
3. Select Display Device from the Service Menu.
4. Select Configure from the Display Device menu, then select Installation.
5. Select Orientation, then choose Floor/Rear, Ceiling/Front or Ceiling/Rear, to
match the installation method.
THE LENS SHIFT MECHANISM CAN BE DAMAGED BY
EXCESSIVE FORCE.
• Ensure that the lens lock is released before adjusting
horizontal or vertical lens shift.
• Do not attempt to move the primary lenses beyond their
normal adjustment ranges.
WARNING
➤
- 3Dimension™ Series 1
- Warranty 3
- Important Safety Instructions 7
- Compliance Information 9
- Table of Contents 11
- List of Figures 15
- 1. Introduction 17
- Using This Manual 18
- Description, Features 19
- Introduction 20
- 2. System Overview 23
- Projector 24
- System Overview 25
- D-73d Remote Control 31
- 3. Installation 37
- Quick Setup 38
- Installation 39
- Considerations 39
- Estimating Throw Distance 40
- Throw Distance (TD) = 40
- Screen width (w) 40
- Ceiling Installation 42
- Floor Installation 42
- 3.0 in. (76.2 mm) 46
- Clearance 46
- Installing the 47
- Optional Anamorphic 47
- Lens Mount 47
- Mounting the D-73d 52
- Mounting the 53
- Interconnections 54
- SECONDARY 55
- Audio Processor/ 56
- Switcher 56
- Secondary Display 56
- Control System 57
- AutoScope Lens Motor 58
- Notebook Computer 61
- HDMI source 62
- COMPONEN T 63
- VIDEO OUT 63
- RGB Camcorder 64
- Gaming Console 65
- DVD/DTV STB 65
- Power-Up Sequence 67
- Alignment Procedure 67
- 16:9 1080i/60 70
- Correct Lens Angle 76
- Incorrect Lens Angle 76
- Wrong Position 77
- Correct Position 77
- Vertical Keystoning 78
- Horizontal Keystoning 78
- Pincushion Distortion 78
- 4. Operation 81
- 4:3 Image on 84
- 16:9 Screen (Display) 84
- 16:9 Display 85
- (Letterbox aspect ratio) 85
- 1080i HDTV Image 86
- 720p HDTV Image 86
- Below Black 88
- Above Black 88
- Saturation 100
- Operation 101
- Primary Alignment 105
- Polarizer 115
- L R 116
- 6. External Control 119
- External Control 120
- Table 6-1. Serial Commands 121
- DBO R/W Yes -100 100 No 123
- DGO R/W Yes -100 100 No 123
- DRO R/W Yes -100 100 No 123
- IBO R/W Yes -32 32 No 125
- IGO R/W Yes -32 32 No 126
- IRO R/W Yes -32 32 No 126
- NFO R/W Yes 0 10 No 129
- Using Discrete IR 134
- (Standard Mode) 135
- (Standard Mode) (continued) 136
- (Extended Mode) 138
- Controller 139
- (continued) 140
- 7. Specifications 141
- Dimension Digital 143
- Specifications 143
- D-73d Dimensions 145
- Supported Timings 146
- 020-1082-02 Rev. A 152
- March 2014 152
Verwandte Produkte und Handbücher für Datenprojektoren Runco D-73d Ultra
Datenprojektoren Runco CL-410 Spezifikationen
(57 Seiten)
(57 Seiten)
Datenprojektoren Runco VX-1000d Spezifikationen
(90 Seiten)
(90 Seiten)
Datenprojektoren Runco CL-610LT Spezifikationen
(56 Seiten)
(56 Seiten)
Datenprojektoren Runco VX-8d Spezifikationen
(88 Seiten)
(88 Seiten)
Datenprojektoren Runco VX-60d Spezifikationen
(126 Seiten)
(126 Seiten)
Datenprojektoren Runco CL-420 Spezifikationen
(72 Seiten)
(72 Seiten)
Datenprojektoren Runco Vision 85 Spezifikationen
(88 Seiten)
(88 Seiten)
Datenprojektoren Runco RS-440LT Spezifikationen
(41 Seiten)
(41 Seiten)
Datenprojektoren Runco VX-8d Spezifikationen
(104 Seiten)
(104 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern