Runco REFLECTION CL-510 Spezifikationen Seite 70
- Seite / 126
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Installation
58 Runco SC-1 Owner’s Operating Manual
PRE
L
IMINAR
Y
All available channels are listed in the Channel Setup menu (Figure 3-30), which describes
how each channel can be accessed and which serves as the gateway for editing, copying
and deleting channels.
Figure 3-30. Channel Setup Menu
To display the Channel Setup menu, press 3 or highlight Channel Setup and press
ENTER or
. The Channel Setup menu appears with the active channel highlighted.
What Appears in the Channel Setup Menu: This menu lists all channels defined so far
and indicates where they are connected on the input panel.
The far-left column lists channel numbers currently defined. If
a channel has been assigned a name, that name appears in
the far-right column; otherwise, the horizontal and vertical
frequencies of the input signal appear here instead. Remaining
columns contain details pertaining to each channel setup,
such as its switcher number (always 0 = projector), slot location, a variety of icons
indicating access to each channel, and an abbreviated description of each signal type.
Signal Type Abbreviations: The Channel Setup menu identifies signal types in a
shortened form. These descriptors indicate what signal information the projector uses to
identify a match for a given channel, and are preceded by either an “i” (for interlaced
signals) or “p” (for progressive signals).
When used with the DHD Controller, the HDMI output signal is represented by either
“pDig” or “iDig.”
Unlocking Channels: Channels are pre-configured at the Runco factory for use with the
DHD Controller, and are locked to prevent the factory settings from being over-written
accidentally. For 1080i and 1080p digital signals, there are separate channels for each
aspect ratio and “ISF” memory preset (day and night).
Before proceeding with calibration, unlock the currently-active channel so that any
changes you make are stored in that channel.
01 0,2 pDig dhd 720p
02 0,2 iDig 16x9 night
03 0,2 iDig 4x3 night
04 0,2 iDig ltrbox night
05 0,2 iDig vwide night
06 0,2 iDig cinema night
07 0,2 iDig vcine night
08 0,2 pDig 16x9 night
09 0,2 pDig 4x3 night
<Enter> = Edit, <Func> = more options
location signal type channel name
Channel Setup
- OWNER’S OPERATING MANUAL 1
- TWO YEAR LIMITED WARRANTY 3
- Safety Precautions 6
- Table of Contents 10
- List of Figures 11
- 1. Introduction 13
- Using This Manual 14
- Description, Features 15
- Introduction 16
- 2. Controls and Functions 17
- Controls and Functions 18
- SC-1 Input Panel 19
- SC-1 Control Panel 21
- DHD Controller Front 23
- DHD Controller Rear 24
- SC-1 Remote Control 26
- 3. Installation 29
- Quick Setup 30
- Installation 31
- Considerations 31
- 20% Offset 35
- Installing the 36
- Projection Lens, Lamp 36
- Lamp/Air Filter 38
- Lamp Cooling Compartment Door 38
- Min. 10” 41
- Extension 42
- Mounting the SC-1 43
- Remove these screws 44
- Pass cables through 44
- Replace these screws 44
- Personal Computer 48
- Red Green Blue Horiz Vert 48
- DVD Player, VCR 49
- Satellite Receiver 49
- Laser Disc etc 49
- 2 Transmit Data 50
- 3 Receive Data 50
- 5 Ground 50
- Rear Panel 51
- AutoScope Lens Motor (Rear) 51
- (male) (female) 53
- Turning on the Power 56
- Component SD NTSC 480i 57
- Cinema SC-1 57
- Maximizing Light 58
- Installing and 61
- Adjusting the 61
- CineWide Anamorphic 61
- Too Far Right 63
- Too Far Left 63
- Correct position 63
- Too High 64
- Correct Lens Angle 64
- Incorrect Lens Angle 64
- Wrong Position 65
- Correct Position 65
- Calibrating Projector 66
- Input 2 (DVI) 66
- Channel Setup 70
- No Resizing 72
- Working With the 78
- 4. Operation 81
- Chroma Delay 82
- 4:3 Image on 84
- 16:9 Screen (Display) 84
- Below Black 87
- Operation 88
- Vertical Keystone Correction 95
- Positive values 95
- Negative values 95
- Safety Guidelines 99
- Maintaining Proper 100
- Maintenance and 101
- Cleaning 101
- Lamp and Filter 103
- Replacement 103
- Remove anode connector 104
- Lens Replacement 107
- Troubleshooting Tips 108
- Table 5-2. SC-1 Error Codes 110
- 6. Serial Communications 113
- Table 6-1. Serial Commands 114
- 7. Specifications 119
- DHD Controller 121
- Specifications 121
- SC-1 Dimensions 122
- SERIAL NUMBER 126
Verwandte Produkte und Handbücher für Datenprojektoren Runco REFLECTION CL-510
Datenprojektoren Runco Q-650i Series Spezifikationen
(108 Seiten)
(108 Seiten)
Datenprojektoren Runco D-73d Ultra Spezifikationen
(152 Seiten)
(152 Seiten)
Datenprojektoren Runco CL-410 Spezifikationen
(57 Seiten)
(57 Seiten)
Datenprojektoren Runco VX-1000d Spezifikationen
(90 Seiten)
(90 Seiten)
Datenprojektoren Runco CL-610LT Spezifikationen
(56 Seiten)
(56 Seiten)
Datenprojektoren Runco VX-8d Spezifikationen
(88 Seiten)
(88 Seiten)
Datenprojektoren Runco VX-60d Spezifikationen
(126 Seiten)
(126 Seiten)
Datenprojektoren Runco CL-420 Spezifikationen
(72 Seiten)
(72 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern